WHAT YOU WILL LEARN IN THIS ARTICLE
- How to prepare your structure for netting
- Properly stretching your netting to fit the perimeter of your structure
- How to fasten your netting
- What to do after your netting is fastened
BEFORE YOU BEGIN
The first step when using netting is to understand how netting behaves. When you first unpack your netting, it will appear longer with the holes in the netting resembling a diamond shape. This is because it has not been stretched out to its full width. Once the netting is stretched out to its full width, the length will shorten and the holes in the netting will become square-like.

When fastening your netting it is very important that you do not over stretch it. This will reduce the netting's durability.
Attaching your netting requires proper attachment pieces. If you are attaching the netting to wire frames, use hog rings. For attaching netting to wooden frames, use staples.
NETTING INSTALLATION STEPS
STEP 1
Before you do anything with your netting, you need to prepare your structure for the netting installation process. To do this, you need to lower any props or supports that will be used to hold up the netting. Make sure that you can navigate safely around both the exterior and interior perimeter of your structure.
STEP 2
Once your structure is prepped and ready, place your bale of netting along the inside wall of your structure.

Then, cut open the top of the bale and locate the end of the netting. (DO NOT dump out all of the netting from its packaging. Doing this will make it harder to stretch out, especially if your netting gets tangled and wrapped around itself). When you locate the end of the netting, hold both corners and start pulling the netting out by walking in a straight line away from the bale. Make sure that you are keeping the net over top of any other wires or small structures that are supposed to be under the netting. Once the netting is stretched out, inspect the net to ensure it is free from damages.
(It is normal to see pieces of the net where the netting may have been split then tied back together. It is a normal part of the manufacturing process.)
STEP 3
After your netting is stretched out along the length of your structure, grab one corner of your netting. Secure the netting corner to the corner of the structure’s perimeter.

Using the mesh chart, determine the number of mesh squares that are equal to 10ft of netting. This is extremely important for the next step.
Begin fastening your netting in 10ft intervals along with the width of your perimeter first. (TIP: Premark 10ft intervals along the perimeter of your structure to speed up the process and attach the netting at the correct locations.) Each 10ft interval should have the equivalent number of 10ft of Mesh squares. (Ex. for 2” Knotted Netting, 10ft of distance along your perimeter should have 40 square meshes in it)
After completing the width of your structure, repeat the exact same process along the length of the perimeter. At this point, you should have two sides of the netting fastened to the structure.
STEP 4
To secure the last two sides of netting, begin by pulling the net to your desired tautness, this should be determined by the size of support posts that are on the inside of your structure that will be holding up the netting. Once you have determined the tautness level, make sure the netting is in a straight line across the pen for even tension and attachment. Repeat the same fastening process along your last two sides. Now that your netting is secured, double check to make sure your netting is lined up properly.
If you have more than one bale of netting, once your sides are fastened, stretch out your second bale of netting and attach it to the perimeter sides it will touch on your perimeter. Then, seam the two nets together with hog rings. Rings should attach every square together so that there are no gaps.



STEP 5

After all of your nets are attached to the perimeter in 10ft intervals and the nets are seamed together, go back over the perimeter and attach the rest of the netting to the perimeter. A ring/staple should be used to attach every other square to the netting. This created a secure attachment of the netting to the perimeter of your structure.
STEP 6
Now that all of your netting is secured completely, you can raise up your props inside to hold up the netting.

WATCH OUT TUTORIAL HERE

